Search Results

RADIATION can produce almost instantaneous failure of modern aircraft lubricants, tests at Southwest Research Institute show. Two types of failures demonstrated are rapid viscosity rise and loss of heat conductivity. Furthermore, it was found that lubricants can become excessively corrosive under high-level radiation. Generally speaking, the better lubricants appeared to improve in performance while marginal ones deteriorated to a greater extent under radiation. When the better lubricants were subjected to static irradiation prior to the deposition test, there was a minor increase in deposition number as the total dose was increased.

FUEL of 97 + octane number gives the most miles for the dollar, present calculations show. At this point, increased efficiency from high compression ratios equals the rising cost of high-octane fuel. For town driving about 95 octane is inherently the least expensive, and over-the-road cars can benefit from gasolines up to almost 99 octane number. This paper describes an analysis made by California Research Corp. of the costs and the value of high-octane gasolines. The economics of octane numbers was based on current commercial practices regarding improved efficiencies of higher compression ratio cars and higher manufacturing costs of higher octane gasolines. The authors believe that if compression ratio and octane number stay in proper relation to each other, the consumer will benefit.

SIMULTANEOUS RECORDINGS of cylinder pressure, audible sound, and crankshaft motion have shown that rumble is a noise associated with bending vibrations of the crankshaft. The vibrations are caused by abnormally high rates of pressure rise near the top dead center piston position. In this study the high rates of pressure rise were obtained by inducting deposits into the the engine. Thud is a torsional vibration of the crankshaft, similar in sound to rumble but resulting from much earlier occurrence of the maximum rates of pressure rise. Rumble vibrations consisted of a fundamental frequency of 600 cps and higher harmonics in the 11/1 compression ratio V-8 laboratory engine used in the investigation. The audible noise of rumble was predominantly composed of the second harmonic or about 1200 cps.

RADIOTRACERS were used to study the wear effects of engine speed, load, jacket water temperature, fuel temperature, and chromium-plated rings in a medium-speed diesel engine. One distillate fuel and two residual fuels were tested. This paper describes the tests and their results. Some of the conclusions are: The brake thermal efficiency with high viscosity residual fuel was essentially equal to distillate diesel fuel over a wide range of loads, providing the residual fuel was heated to the proper temperature. Engine speed did not affect the wear rate of cast-iron rings when distillate fuel was used, while with residual fuel wear decreased with increased speed. With distillate fuel, engine load had essentially no effect on cast-iron ring wear. With residual fuel, decreasing engine load produced a marked increase in ring wear*

Abstract With the adoption of Vehicle-to-everything (V2X) technology, security and privacy of vehicles are paramount. To avoid tracking while preserving vehicle/driver’s privacy, modern vehicular public key infrastructure provision vehicles with multiple short-term pseudonym certificates. However, provisioning a large number of pseudonym certificates can lead to an enormous growth of Certificate Revocation Lists (CRLs) during its revocation process. One possible approach to avoid such CRL growth is by relying on activation code (AC)-based solutions. In such solutions, the vehicles are provisioned with batches of encrypted certificates, which are decrypted periodically via the ACs (broadcasted by the back-end system). When the system detects a revoked vehicle, it simply does not broadcast the respective vehicle’s AC. As a result, revoked vehicles do not receive their respective AC and are prevented from decrypting their certificates.

This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.

This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.

The Swedish Biomimetics 3000's μMist® platform technology has been used to develop a radically new injection system. This prototype system, developed and characterized with support from Lotus, as part of Swedish Biomimetics 3000®'s V₂IO innovation accelerating model, delivers improved combustion efficiency through achieving exceptionally small droplets, at fuel rail pressures far less than conventional GDI systems and as low as PFI systems. The system gives the opportunity to prepare and deliver all of the fuel load for the engine while the intake valves are open and after the exhaust valves have closed, thereby offering the potential to use advanced charge scavenging techniques in PFI engines which have hitherto been restricted to direct-injection engines, and at a lower system cost than a GDI injection system.

Using renewable fuels is a reliable approach for decarbonization of combustion engines. iso-Butanol and n-butanol are known as longer chain alcohols and have the potential of being used as gasoline substitute or a renewable fraction of gasoline. The combustion behavior of renewable fuels in modern combustion engines and advanced combustion concepts is not well understood yet. Low-temperature combustion (LTC) is a concept that is a basis for some of the low emissions-high efficiency combustion technologies. Fuel ɸ-sensitivity is known as a key factor to be considered for tailoring fuels for these engines. The Lund ɸ-sensitivity method is an empirical test method for evaluation of the ɸ-sensitivity of liquid fuels and evaluate fuel behavior in thermal. iso-Butanol and n-butanol are two alcohols which like other alcohol exhibit nonlinear behavior when blended with (surrogate) gasoline in terms of RON and MON.

Prior theoretical work relating barrier equivalent velocity (BEV) and change in vehicle velocity, ΔV, has either neglected restitution or mischaracterized its role. Based on fundamental structural dynamics principles, improved relationships between BEV, ΔV, coefficient of restitution, and vehicle mass and stiffness are formulated. These corrected relationships are then utilized in the assessment of four classes of vehicular impact testing: vehicle to vehicle (VTV), vehicle to infinitely massive rigid barrier (VRB), vehicle to infinitely massive compliant barrier (VCB) and vehicle to finite mass movable rigid barrier (VFMB).

Φ-sensitivity is a fuel characteristic that has important benefits for the operation and control of low-temperature gasoline combustion (LTGC) engines. A fuel is φ-sensitive if its autoignition reactivity varies with the fuel/air equivalence ratio (φ). Thus, multiple-injection strategies can be used to create a φ-distribution that leads to several benefits. First, the φ-distribution causes a sequential autoignition that reduces the maximum heat release rate. This allows higher loads without knock and/or advanced combustion timing for higher efficiencies. Second, combustion phasing can be controlled by adjusting the fuel-injection strategy. Finally, experiments show that intermediate-temperature heat release (ITHR) increases with φ-sensitivity, increasing the allowable combustion retard and improving stability. A detailed mechanism was applied using CHEMKIN to understand the chemistry responsible for φ-sensitivity.

This study proposes a novel biofuel for spark ignition (SI) engine, α-pinene (C10H16), which is non-oxygenated and thus has a gravimetric energy density comparable to that of hydrocarbon fuels. The ignition characteristics of α-pinene were evaluated in an ignition quality tester (IQT) under standard temperature and pressure conditions. The measured ignition delay time (IDT) of α-pinene is 10.5 ms, which is lower than that of iso-octane, 17.9 ms. The estimated research octane number (RON) for pinene from IQT is 85. A temperature sweep in IQT showed that that α-pinene is less reactive at low temperatures, but more reactive at high temperatures when compared to isooctane. These results suggest that α-pinene has high octane sensitivity (OS) and is suitable for operation in turbocharged SI engines. With these considerations, α-pinene was operated in a single cylinder SI engine.

The sweetpotato (Ipomoea batatas L. LAM.) is a versatile and underexploited food crop. Consumption of sweetpotato based processed foods provide β-carotene, which is the major precursor of vitamin A. The sweetpotato has the potential to provide antioxidants that may help reduce the radiation risks astronauts face while in space. Therefore the objective of this experiment was to evaluate β-carotene in dehydrated hydroponic sweetpotato cultivars. Hydroponic cultivars WHATLEY/LORETAN and NCC-58 were grown with and without 7-10 μmole of light. WHATLEY/LORETAN contained the highest amount of β-carotene content average of 31 μg/100g in dehydrated hydroponic sweetpotatoes compared to NCC-58 with 18.5 μg/100g.

Dynamic skip fire (DSF) has shown significant fuel economy improvement potential via reduction of pumping losses that generally affect throttled spark-ignition (SI) engines. In DSF operation, individual cylinders are fired on-demand near peak efficiency to satisfy driver torque demand. For vehicles with a downsized-boosted 4-cylinder engine, DSF can reduce fuel consumption by 8% in the WLTC (Class 3) drive cycle. The relatively low cost of cylinder deactivation hardware further improves the production value of DSF. Lean burn strategies in gasoline engines have also demonstrated significant fuel efficiency gains resulting from reduced pumping losses and improved thermodynamic characteristics, such as higher specific heat ratio and lower heat losses. Fuel-air mixture stratification is generally required to achieve stable combustion at low loads.

Abstract An investigation into the pre-ashing of new gasoline particulate filters (GPFs) has demonstrated that the filtration efficiency of such filters can be improved by up to 30% (absolute efficiency improvement) when preconditioned using ash derived from a fuel-borne catalyst (FBC) additive. The additive is typically used in diesel applications to enable diesel particulate filter (DPF) regeneration and can be added directly into the fuel tank of the vehicle. This novel result was compared with ash derived from lube oil componentry, which has previously been shown to improve filtration efficiency in GPFs. The lube oil-derived ash utilized in this work improved the filtration efficiency of the GPF by −30%, comparable to the ash derived from the FBC additive.

Consideration of the approaching ‘energy crisis’ reveals two requirements for future light duty automotive engines. 1) maximum economy and 2) the ability (perhaps with detail design re-optimisation) to accept a range of fuels of petroleum or other extract, of differing ignition characteristics. One combustion system which meets these requirements is the MAN ‘FM’, the potential of which has already been demonstrated in truck-size engines but on which little information has been published in light-duty engine bore sizes. The paper describes both design and experimental work carried out to evaluate the application of the FM combustion system to a light duty passenger car engine. Consideration is given to the critical design parameters associated with the application of the FM system to a multi-cylinder gasoline based engine and how the criteria can be met. Details of the design and construction of a single cylinder derivative of the multi-cylinder engine are given.

Whether we live on land, underwater, or out there in space, what makes it possible is our ‘skin’. The one we were born with, the one we wear, the one we live in, and the one we travel in. The skin is a response to where we live: it protects as our first line of defense against a hostile environment; it regulates as part of our life-support system; and, it communicates as our interface to everything within and without. In the context of space architecture – we, our space suits, vehicles and habitats are all equipped with highly specialized ‘skins’ that pad us, protect us and become an integral part of the design expression. This paper approaches the subject from a holistic perspective considering ‘skins’ and their manifestation as structure, as vessel, as texture, and as membrane. The paper then goes on to showcase innovative use of materials in practice through two case studies: the ‘spacesuit’ and ‘inflatable habitats’.

As a typical parameter of the road-vehicle interface, the road friction potential acts an important factor that governs the vehicle motion states under certain maneuvering input, which makes the prior knowledge of maximum road friction capacity crucial to the vehicle stability control systems. Since the direct measure of the road friction potential is expensive for vehicle active safety system, the evaluation of this variable by cost effective method is becoming a hot issue all these years. A ‘wheel slip based’ maximum road friction coefficient estimation method based on a modified Dugoff tire model for distributed drive electric vehicles is proposed in this paper. It aims to evaluate the road friction potential with vehicle and wheel dynamics analyzing by using standard sensors equipped on production vehicle, and fully take the advantage of distributed EV that the wheel drive torque and rolling speed can be obtained accurately.

This paper discusses the use of electromechanical devices as the kinematic portions of a microprocessor based gas turbine control system. Specific applications are: 1. An electric motor driven, positive displacement pump, which provides metered high pressure fuel to the distribution manifold. Fuel metering to be provided by varying the motor angular velocity. 2. An electric motor driven lube oil pump. 3. Electromechnical actuators for motion and control of compressor and power turbine variable geometry. 4. A starter/generator integral with the gas generator. Topics covered include: Comparison to conventional hydro-mechanical systems. Response characteristics of the fuel pump and actuator systems. Brushless D.C. motor characteristics. Power electronics requirements for brushless D.C. motors. Control electronics interface with brushless D.C. motor systems. Reliability and maintainability issues. Diagnostic/prognostic enhancements.